12GA rifle From Hell--

[hubel458]

Answering questions; bullet jackets from copper tubing
caps. This process makes jacketed slug with covered
nose. With heavy soft jacket as opposed to a
solid turned slug from solid rod or soft lead slug.

1/2" caps can make .700 and 12ga size jackets.
5/8" caps can do 8ga and maybe 10ga jkts.
And 3/4" caps can make 4ga. These cups are
malleable enough to shape into jackets,
without a 20 ton stamping press.

Interesting info about our posting of this subject on
about 5 dozen forums. One big general forum thread,
that we posted some info, has about 5 million views.It is
Mil Photo Forum a big world wide forum..
The top forum of the bunch, with whole thread on it
about 120,000 views, 2nd about 110,000 views, 3rd one
about 104,000 views, 4th one about 102,00 views.
We greatly appreciate all the interest from all
the forums, of all sizes. And all the help
and ideas too...Ed

[hubel458]

You know of the 4 bore we did on falling block,
with its 1 inch bore.Using turned cases and cases
made from 20mm brass. Our cases have a rim and
straight sides. A smith in the EU made a 1 inch bore
gun on a bolt action, using 20mm brass expanded
to take 1 inch bullets. His case has a shoulder to
head space on. It is called the Inch Gun by some.
It is a really nice looking gun, with great
craftsmanship.Ed

[hubel458]

Here is picture of the 8ga falling block we are working
on, partly done. It is built like the 4bore one in a
one piece stock. IT is built .150" narrower than 4bore.
We used the heavy 8ga barrel that I first
put in the Enfield bolt gun for a 8ga testing. The breech
block, linkage, lever, pivot is done, as you can see
in picture with lever open and breech down.
I have got to chamber, put in firing pin, do
hammer and trigger. 8ga gun in 1st picture.

Hammer and trigger setup is now mounted and moves
on the back of the breech block on an extension.
I also made this change first on 4bore, 2nd pic.
It uses NEF hammer and spring and Stevens trigger.
Breech block set up same as 4bore just narrower.
Later hope to do a 2 bore and same setup only
breech and action a little wider.Ed

[hubel458]

Here picture of the 8ga from back. This action will also
do 12ga FH, 10ga, 700HE, 600NE,50BMG,etc. The breech
block in this and the 4bore are 1 inch thick front to back,
with the width different. The bottom of block is same on all
and uses same linkage and lever; same hammer and trigger.
The 4bore one will do 20mm, as that is what I make
the 4bore brass from. When I do 2bore, breech block will use
same design, but just be wider on the top of the block.
The recoil pads are over 2" thick. I made the stock
from a 2.5" thick blank......mostly by hand.

This action will hold much more pressure that the heavy
built plastic 8ga cases can take , and they are good
to over 20,000 psi. Like a 1000gr at 2500.Ed

[hubel458]

Guys wanted more particulars of Hubel FB..
Here is picture, empty falling block receiver
from the top...2nd a side view of the breech
block with back extensions, with hammer and
trigger. Hammer has safety cocking notch.
The lever, not shown, connects to linkage up
inside the two bottom extensions.Ed

[hubel458]

A fellow in Texas picked up a Tula-Toz 4bore
pump gun like Big Al has. He is getting some
of the 3 inch brass 4ga cases from RMC.
RMC still has them if anyone needs them.
That gun takes a short 4ga case, either brass
or plastic if you can find them.This 4 gauge
is a .938 inch bore, smaller than our 1 inch one.
Pic is Al's gun.Bolt has 4 locking lugs...ED

[hubel458]

Here are pictures of the Falling Block breech block.
Front and side rear view....Notice the integral bottom
extensions are narrower than the top. These are
what the linkage is inside of and when breech is
levered down these fit though the slot in the stock.
And being narrower the slot isn't too wide so the
stock has enough strength. Bottom extensions same
width for all action sizes.Just top different
for the size of action needed for big cartridges.
This breech is little rough as it has had a dozen
changes to it. But it holds a load in 4 bore
of 1500gr over 2600.Ed

[hubel458]

Some more slug ideas--First picture of 10ga 830gr
hollow base slug in 8ga wad cup, And 690gr hollowbase
69 caliber Dixie Gunworks slug that I swaged down a
little, in a 12ga wad cup.
2nd picture is the a new offering from the EU,a
new 300gr US-S slug with locked on base, discarding
petals, by European Cartridge. Accurate in smooth bores.
In 3" plastic they load to over 2100 with shotgun
powders. In a 3.5" plastic and our slower powders
I could get over 2800. Ed

[hubel458]

That US-S pointed slug with discarding petals,
and locked on base, shown above is called the
Swift 12. And correction on the weight, it is 320 gr.
And they plan on testing and maybe supplying 3.5"
versions, planning on getting around 2500 fps with
shotgun powders. I know in our 3.85" case in the long
barrel Savage, I could get over 3000 with big amounts
of our slower powders we load with.

Bought some tubing caps And here is picture
of those copper tubing caps, you can make bullet
jackets out of, and fill with lead. In picture you see
a rough one I formed with punch, and with a die they be
perfectly formed. And with right die they could be
formed with round nose with edge step for perfect roll
crimping in plastic. And on the right see big caps that
would do 4 bore.There are caps between the two sizes
that would do 8ga...Ed

[hubel458]

More 12gs slug/sabot info-- About discarding sabots.
Most factories making sabot slugs make them relatively light,
300 to 350 grains, and that is why they are on average
more accurate than what guys try to reload with heavier
slugs in the sabots. Reason is light slugs don't damage
the sabot, while they are trying for high velocity.
Example is picture of Hornady SST sabot and it only has
a one way plastic seal over powder, and a hard
rubber cushion inside the sabot under the 300gr jkt
spitzer style slug. Many 12ga hunters say these are
the most accurate.

Another slug idea is a blunt nose jacketed slug of
675gr I made from one of RG's hollow point jkt slugs.
I cut part of jacket off of the front and swaged
it over to make blunt nose. These are for the guys
trying to make short loaded brass case rounds
in 2.5" brass and 2.62" brass to be no more than
2.75" overall to work in certain guns. it is
on left, 2nd pic. And gets good velocity with just
good BPGS seals under it and slower powder.
On right is US-S sabot with discarding petals, locked
on base we tried in short brass case, and can't, due
to length of sabot get in enough powder to get
the higher velocity with heavy 700gr US-S slug, the
guys want to get.....ED

[hubel458]

Here is picture some folks wanted of our
big cases with smaller 30-06 for comparison.
In picture, 1st my 2ga, 4ga, 8ga, 10ga, 12ga,
my 700HE long case, my 700H 3.25", and 06.

2nd picture is short 2 5/8" brass cases we
are checking loads in, to see how much speed
can be gotten.You can easily see the length of
short full bore lead slug, compared to the
saboted ones, allowing more powder in the short
slug load for more speed..

Now this doesn't mean saboted are no good, or
that I don't like these saboted types. Great for
smooth bores, the US-S with locked on base, are
the best there is, I think, for big game.Just
got to use longer cases. I always felt, that going
longer cases is worth the effort where practical ED

[hubel458]

Here is picture of my big 585 cases.
30-06 for size comparison.
3rd is 585HE - I have it in bolt, falling block,
break, etc, actions.

1st is 585 Hubel Super Magnum - Designed
for strong bolt guns. Have in a MRC PH.
Can get 20,000 ft lbs.

2nd 585 Rimmed Hubel Magnum and I have it
now as a single shot in an 1887 Win.
The 87 has a 30" heavy barrel. Case is
designed to use in break actions and run about
25,000 psi, but due to the size of the case
has enough powder so can get 15,000 ft lbs.
It is 4" long, and could be called 24ga FH.Ed

[hubel458]

Some 10ga experimenting with slug loads.
In NEF with 32" factory, long bull barrel.
It is smooth so we use hollowbase slugs

Cases FED 3.5" plastic cases, roll crimped.
900gr full bore slugs -180 gr RE17- 1800 plus.
Use plastic powder seal and fiber wads.
Slug hollowbase and hard cast.

740gr 69cal hollowbase soft lead slug, in VP100
10 ga wadcup. Deep hollowbase slug ..Wadcup has own seal
and cushion. 180 gr RE17 -- 2000+ fps.

Here are pictures of a couple other different guns in
my long 585HE cartridge.. 1st is Olympic Arms
BBK bolt gun, in a target style stock with palm
swell pistol grip...2nd is the one I made on a CBC
single shot by mono-blocking in a heavy 585 cal
barrel. Barrels- CBC breach 1.18"-- BBK breach 1.32"
1.070 muzzles.Ed

[hubel458]

Some 28ga FH info and ideas.
Brenneke now has 28ga slugs, with good speed,
decent smooth bore accuracy. About 260 grain
slugs. SAme style as their 12ga ones with locked
on base.Work in 28ga NEFs of course and
28ga O/Us.Some real good 28ga O/Us out there.
28ga is a .550 Inch bore.

But now Rossi has out, a revolving 28ga shotgun
with about a 19 inch barrel. Should work ok with
those slugs. You could also get RMC 28ga brass cases
about 2 3/4" long, maybe 3", depending on chamber,
a shorter version of our 28GA FH 3.25" case.

Maybe I get one in the future, and put on a longer
heavier 585 cal barrel and set it up for my
585 Short HE. Have a switch barrel 28ga/585.
Neat gun.Called Circuit Judge....Ed

[hubel458]

I found a picture of 28ga Rossi Circuit Judge. Barrel is
smooth bore , could be little heavier barrel, but it will do
ok with the new plastic case Brenneke slugs,
260 gr at 1450 fps..Could do 2000 in a little longer
brass case from RMC.

28ga is a 550" bore in a rifled bore.
24ga is about .585 same bore as my 585, and
most all 577/585 stuff. The 28ga chamber with minimum work
would fire my shorter 585 with a switch barrel 585 bore.
And still work with 28ga with 28ga barrel put on.
Difference is the case thickness with the 28ga case
being nearly the same OD as my 585 drawn, stronger
brass cases.

The Brenneke slug has a long locked on base and seal,
connected by long post, that you can see inside
the case in picture and pictured on the box
Quite a long tail so to speak for
good smooth bore work.This is a great step forward
for 28ga slugs, as most reloading slug stuff was only
100 grain balls or other super light slug designs...ED