Hunt Chat  

Go Back   Hunt Chat > Tools of the Trade > Knives and Blades

Reply
 
Thread Tools Display Modes
  #1  
Old 02-08-2009, 03:13 PM
Rancid Crabtree Rancid Crabtree is offline
Registered User
 
Join Date: Jul 2008
Location: WI
Posts: 191
Super glue finish build along

After receiving lots of questions on how to do a super glue finish on a knife handle I decided to show the steps. This is not to say that this is the only and proper way to use super glue as a finish. It's just the way I do it. Super glue is used on tropical woods that have oils that prevent most finishes from drying, curing or hardening. It can be used on any wood.

First of all, This is for small projects since it is not really cost effective for large projects. At the same time, there are those that use a super glue finish on pool cues, pens, bowls, chess pieces and a host of other projects.

I went out and bought a 4 pack of .07 Oz. tubes for $1.99. I bought the regular and not the gel but have heard of people using the gel with good results.



Always read the warnings and understand the risks. I have chosen to ignore rule number four. I found rule number five a bit odd. I do want good results but I fail to see why it matters how me and the missus spend our free time or if we are good at it.

This glue is stinky but larger containers that are more expensive can be bought in a low odor version.



I used a scrap piece of Bubinga right off the saw. I did not sand it at all. I did this to show that super glue is gap filling and fills in the pores of the wood. I poured a small drop on the wood.



And spread it around with this brush. This is one of a set of ten brushes that I got from my parent on my birthday. I've had them for 44 years.



I just spread it out until the piece is covered and never stop moving. It stays liquid for a short while.



And then hardens with a little less gloss. You can see the rough saw lines on the wood. but after I build up of a few coats, it will smooth over the bumps. *** DO NOT blow on it to dry it faster.



After two coats, I use 400 grit sandpaper to smooth out the brush marks and then wipe it with a clean cloth to remove the white dust.



On the back side of the piece I applied the same number of coats except on the last one, I blew on it to dry it faster and you can see the results. The water vapor in your breath makes the glue cloudy or foggy and you cant un-do the damage. You will have to sand it all off and start over. The same goes for touching the wet glue with your finger. The moisture in your skin will also turn the glue white.



After a few coats, you also get a build up on the tip of your brush.



Nail polish remover (Acetone) will remove the hardened glue. I wet a paper towel and set my finger in it.



I will also use some of that same 400 grit to clean of any glue left behind. Now the brush is clean.



Once hardened, I use 400 grit and 0000 steel wool to smooth the finish.



Super glue leaves a hard, crystal clear and water proof protective coating of acrylic plastic on the wood.



It can be buffed to a high sheen.



Give it a try the next time you are working on a small wood project or if making fishing jig heads or turkey calls or pistol grips, etc. Work outside or in an area with good ventilation.
__________________
http://staysharpguide.com/
Reply With Quote
  #2  
Old 02-08-2009, 03:48 PM
Swift Swift is offline
Registered User
 
Join Date: May 2001
Location: PA
Posts: 1,003
Good write up!
__________________
220 Swift still King
Reply With Quote
  #3  
Old 02-08-2009, 11:03 PM
Jack Jack is offline
Moderator
 
Join Date: Jun 2002
Location: Georgia
Posts: 6,085
Interesting! Thanks, Rancid.
__________________
“May we never confuse honest dissent with disloyal subversion.”
Dwight D. Eisenhower
"If the freedom of speech is taken away, then dumb and silent we may be led, like sheep to the slaughter"
George Washington
Jack@huntchat.com
Reply With Quote
  #4  
Old 05-08-2009, 02:08 AM
neologist neologist is offline
Registered User
 
Join Date: May 2009
Location: Seattle Area
Posts: 1
Thank you for that. Who wudda thought?
Reply With Quote
  #5  
Old 05-08-2009, 09:56 AM
blacktail blacktail is offline
Moderator
 
Join Date: Dec 2002
Location: Southern Alberta
Posts: 764
did the same thing on a couple of my latest pieces

works well
__________________
Promoting the sport of Archery and Bowhunting
NCCP,IBEF Certification

Custom Knife Maker
www.blacktailcustomdesigns.com

quote....."Life's tough.....it's even tougher if you are stupid".....John Wayne
quote....."It is far better to be alone than in bad company".....George Washington
Reply With Quote
  #6  
Old 01-18-2010, 02:33 PM
cordell cordell is offline
Registered User
 
Join Date: Jan 2010
Location: Virginia
Posts: 29
Excellent Post

Rancid Crabtree,
Let me begin by saying that your writing skills are exceptional. I have enjoyed all the posts that I have read so far, and truly enjoy seeing your knives as they progress. Please continue the tidbits of information, they are most welcome. Take care and God bless....cordell P.S. I didn't understand the need for #5 either...................... TC&GB..c
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:42 PM.


Powered by vBulletin® Version
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd.