Hunt Chat  

Go Back   Hunt Chat > Tools of the Trade > Rifles

Reply
 
Thread Tools Display Modes
  #76  
Old 11-10-2007, 01:59 AM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
Had a light barrel 87 12ga replica now
it is this Long Tom slug gun.....Ed


__________________
Ed Hubel
Reply With Quote
  #77  
Old 11-19-2007, 07:52 PM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
Got an 8ga barrel blank being made now,
will be here end of the week.Found this
info on plastic 8ga kiln gun loads, they
load a frangible 710gr slug at 2300-
for 8300ft lbs, load 1275gr hard slug to
1700, 8100 ft lbs. We will outdo those easy
with our non-shotgun powder loads, in
a heavy barrel. We setup an Enfield for 8ga.
In the 87 long barreled gun we will be testing
Breneke slugs. Guys are reporting good accuracy
in smooth and rifled barrels. The pictured barrel
on 87 is smooth and we will see how the
slugs in pic stand some speed.Ed


__________________
Ed Hubel
Reply With Quote
  #78  
Old 12-01-2007, 01:13 AM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
Tested 35" smooth barrel in 1887. Got couple
1 oz foster slugs over 2400, with 110gr
of 4227. 3" plastic case, regular primers.
This is a heavy barrel for that type of load,
don't do this in your 12ga skinny barrels.
The 28GA FH cases on the way.Chambering
bolt gun for it now..Ed
__________________
Ed Hubel
Reply With Quote
  #79  
Old 12-13-2007, 02:02 AM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
In the 87 long smooth barrel got
1 oz Brenneke to 2400 with 110gr
of 4227, You could use 4759 and
VV110 also at lesser amounts.
Barrel is cylinder bore size.
Brenneke slugs need no wads as the
locked on wad works good.Ed
And going heavier in 87 got 600 grain
Dixie over 2000, got a Buckhammer slug
I took out of factory load over 1900.
Buckhammer and locked on wad is 630
gr. Tested in 3" plastic cases.

The firing pin on the 87 didn't protude out
like I like them to as it comes from factory,
so I removed .015 from the hammer stop.
It fires big and small primers perfect.Ed
__________________
Ed Hubel
Reply With Quote
  #80  
Old 12-23-2007, 09:28 PM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
10GA FH..a NEF 10ga, medium to heavy wt smooth barrel.
28" long, gun weighted to 14lbs. Factory FED 765gr loads
are 1300 fps. 200 gr of first powder tested is 7383 surplus
and the regular shotgun primers got 765 gr to 1600,
for 4300 ft lbs. Case won't hold anymore 7383.
Federal factory hollowbase slug is .025" smaller than
10ga bore. I bumped it up to the .775" size, by expanding
hollow base. With 7383 that gave another 150 fps.Fast starting
shotgun powders expand base better than much slower 7383.
The Federal factory load has 120gr of wads/seals about 1.4"
long. Better to replace with much more slower powder,
getting better velocity, still at low shotgun pressures.Ed
We will test 4227 with the same slug , and saboted slug
of some design. We roll crimped with crimper in drill press.
Case expansion with 7383 very little(.006") like
the factory loads. 3.5" plastic.Used one .050 wad.Ed
__________________
Ed Hubel
Reply With Quote
  #81  
Old 01-05-2008, 12:59 PM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
In 10GA NEF 110gr 4227 got 765gr slug
to 1800, ejected ok. If it was a really
heavy barrel it could do more.Using the
7383 surplus at 150 gr, don't even have
to resize to fire 3 times. The 28GA FH
done and testing in next couple weeks.Ed
__________________
Ed Hubel
Reply With Quote
  #82  
Old 01-09-2008, 10:20 PM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
Fired 28GA FH-- Cases extract easy.--It is
in bolt action Enfield. With 550gr jkt slug,
full load 150 gr of WC-860, got 1900 fps.
This will be slowest load and powder.
In picture is 3.25" brass 28ga cases, regular
28ga plastic case, jkt slugs, a 458Win
for comparison.Regular cases work also.Ed

__________________
Ed Hubel
Reply With Quote
  #83  
Old 01-10-2008, 11:34 PM
hofts hofts is offline
Registered User
 
Join Date: Jan 2001
Location: sioux falls sd
Posts: 276
uh what

uh yeah, what?
Reply With Quote
  #84  
Old 01-13-2008, 10:58 PM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
28ga cases are made by Rocky Mtn Cartridge,
Barrel is rifled with 4 grooves, 1-22 twist.
You could do one on Savage 210.Another
shotgun bolt action that would handle it
with little work, heavy barrel, is the
395-495-595-695 bolt action Mossberg.
Just to show that 28GA FH isn't puny, here is
picture of it next to a 505 Gibbs.Ed


__________________
Ed Hubel
Reply With Quote
  #85  
Old 01-18-2008, 11:21 PM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
Here is picture and info on Royal
Arms' site for hopped up 12ga loads,
used in little cannons for bomb work.
Anyone got any of these fired that I could inspect to see how they are built.ED

http://www.royalarms.com/EOD/ammo/canonammo.gif
__________________
Ed Hubel
Reply With Quote
  #86  
Old 01-28-2008, 09:48 AM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
I like the Savage 210 so I'm putting
a 700 barrel on one and chambering for
my 700H 3.25 case. Working on it now.
It is a straight belted case, .700 cal.
Should get the same energy levels as
the 12GA From Hell case in same action.
In pic is 700H case in the action.
There is guy building a 600 Nitro
in 210 also. Ed

__________________
Ed Hubel
Reply With Quote
  #87  
Old 02-06-2008, 02:06 AM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
28GA FH research. Guy on forums suggested using 54cal
rifled barrels for 28ga as they are easy to get. I looked into
it and did some testing. It is ok as long as you keep bullet
about 400gr as most 54cal barrels are not super alloy.
You got to use the thick heavy ones also, being stronger.
And everyone with 28ga wants slugs and there is no slug loads
from factory, and to reload the heavier bullets we shouldn't use
these barrels or regular 28ga barrels with 600-700 gr slugs.
But there are couple dozen 54cal bullets out there
stocked all over the gunstore shelves, in weights from 300 to
450 gr. There are heavier but for 28GA FH on deer 400gr is
great. I tested the 405 gr copper plated Powerbelt brand, with
velocities from 2300 to 2800 plus fps. That's 6500 ft lbs.
The 54cal slugs load tight in the RMC 3.25" 28ga case fine by
sizing top a little tighter. Bullet obturates to fit .550 bore
as bullet is hitting target straight. A lot of 54cal barrels
go from 530 to 560. 54cal slugs range from .534 to .560"
There are different sizes of 28ga barrels and chokes,
so some where there is lighter 54cal slug that fits..
And with light slugs the pressure limits with the MRC brass
match top muzzle loading pressures, so these barrels will work.
And great thing is the 54cal barrel guys ain't allergic
to making long barrels. I've shot one MRC case 15 times and
still going strong...Ed
__________________
Ed Hubel
Reply With Quote
  #88  
Old 02-12-2008, 02:40 PM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
28GA FH testing. 405 gr in 2.75" plastic case
got 1400. Tested the Great Plains 54cal
lubed slug, runs from 2200 to 2700. It is
by Hornady and its front band actually measures
.550" and hollowbase. They hit target straight.
Got a bunch of 415gr hollowbase coming that
are 548" from Dixie Gunworks. Only 26 cents each.
All will work in plastic or long brass
case. I found another .550 bbl and coming, and
it will go on a Mossberg bolt action
for the second 28GA FH to test.. Ed
__________________
Ed Hubel
Reply With Quote
  #89  
Old 02-20-2008, 12:06 AM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
tested the 415 gr hollowbase slugs in 28GA FH long
brass case. These are ones that Dixie Gunworks sell
that they call their Sharps .548" slug. They all run
about .008 bigger than that so they make perfect tight
fit for .550" barrel, and I used a good lube on them
in the grooves. They are a little harder alloy slug than
the Powerbelts or Great Plains The 28ga shellholder
for our Lee, Lyman, Rcbs presses , we use, is from
RCBS for regular metallic press rams. For 28ga dies
Hollywood made some for metallic presses.Also for
sizing for bottom 2/3 of the brass case you can cut
top off of the 500J die.The slower powder loads don't
even have to have the bottom half sized, which
is great for a turned case. If we had drawn brass cases
we could get 11,000 ft lbs, in the Enfield, which we
don't really need for deer. 4-6000 ft lbs ok/deer ..Ed
__________________
Ed Hubel
Reply With Quote
  #90  
Old 02-29-2008, 01:55 AM
hubel458 hubel458 is offline
Registered User
 
Join Date: Mar 2003
Location: Brinton,Mich.
Posts: 336
Here is picture of a jacketed hollowpoint
12ga slug a fellow is going to make for us.
We hope to have tooling set up this summer
we plan on. Next to it is a 600gr Dixie hardened
slug. First ones he will probably make will
be about 700-750 gr.Ed

__________________
Ed Hubel
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:22 PM.


Powered by vBulletin® Version
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd.