Hunt Chat  

Go Back   Hunt Chat > Tools of the Trade > Reloading Bench

Reply
 
Thread Tools Display Modes
  #1  
Old 02-25-2009, 06:46 PM
Karl Peterson Karl Peterson is offline
Registered User
 
Join Date: Feb 2009
Posts: 12
Question Another "New guy" question. Brass

In the past, I have been shooting factory ammo. I have 60 - 100 brass cases of several different kinds of ammo. About 200 casings in all. WIN, Hornady, Remington, etc.
Now that I am reloading, should I get rid of this brass and start with new brass? Also, what is the general opinion on nickel brass.
Reply With Quote
  #2  
Old 02-25-2009, 07:50 PM
Adam Helmer Adam Helmer is offline
Moderator
 
Join Date: Jun 2002
Location: Mansfield, PA
Posts: 3,865
Karl Peterson,

Welcome to the Forum; I see this is just your 6th post.

I suggest you separate your brass by by manufacturer and keep them separate; plastic baggies are made for this task. Check each lot of brass for length and trim as needed. Be sure to champfer and deburr your cases before reloading. Do not get rid of that brass, especially if you fired it in the arms you will reload for in the near term.

I like nickel brass. In the .38/.357 it never grew green crud while in leather belt loops on my duty belt like brass cases always did. I like nickel .30-06 cases because I reform them for my .35 Whelen and never get my .35 Whelen and .30-06 ammo mixed up.

Again, welcome to this site. Be well.

Adam
__________________
Adam Helmer
Reply With Quote
  #3  
Old 03-15-2009, 12:48 PM
Talon's Avatar
Talon Talon is offline
Registered User
 
Join Date: Aug 2003
Location: Arizona
Posts: 71
Re-load it. Pay attention to detail check brass always for signs of stress.Keep a simple log of each time you re-load the same brass.

Dont worry about it being nickle

Talon
__________________
Have a Cigar

Take your time...Don't live to fast....
Troubles will come...And they will pass...
Reply With Quote
  #4  
Old 03-15-2009, 05:58 PM
Catfish Catfish is offline
Registered User
 
Join Date: Jan 2001
Location: Oh.
Posts: 1,607
If your shooting a bolt gun it would probly be a good idea to seperate your brass by manufacture if your wanting the best accuracy you can get as the case capicaty will very a small amount from 1 brand to another. I carry an AR some when hunting coyotes and for it I pay no attention to brass manufacture. With mixed brass I have no trouble getting sub moa groups and this rifle I carry when expecting shooting a running coyotes. As for nickle brass if you have it use it, if you don`t have any don`t by any. The problem with nickeled brass is that the cases will split with alot fewer loadings than regular brass. There is no differance in velocity or accuracy.
__________________
Catfish
Reply With Quote
  #5  
Old 03-16-2009, 10:14 AM
Karl Peterson Karl Peterson is offline
Registered User
 
Join Date: Feb 2009
Posts: 12
Thanks for your time and advice.
Karl
Reply With Quote
  #6  
Old 03-16-2009, 10:15 AM
Karl Peterson Karl Peterson is offline
Registered User
 
Join Date: Feb 2009
Posts: 12
Thanks again for your help.
Karl
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:40 AM.


Powered by vBulletin® Version
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd.